Traction Aiding Devices (from last Forum)


[Follow Ups] [Post Followup] [Dodge Power Wagon Forum]


Posted by Clint Dixon on Thursday, March 15, 2007 at 21:25:09 :

There seems to be some basic confusion relating to the design and operation of various traction aiding devices available for the axle housings in our trucks. I will be the first to admit that I don’t know everything about any one thing, a little about a lot of things, and just enough to get myself into trouble on most things. I have owned several vehicles with standard differentials in the axle housings. I have owned two vehicles with limited slip traction aiding devices in the axle housings. And, I have owned one vehicle with a positive locking traction aiding device in the axle housing. I have never owned a vehicle having no means within the axle housing to compensate for different rotational speeds between the two axle shafts located at either ends of the common housing.

So, with that in mind, I have been trying to help where I can, with what information I have, to help clear up the basic confusion that exists on this subject. I have also been struggling to pinpoint and to understand just what exactly the confusion is. I do not feel that I have completely realized the whole scope of the confusion so my premature attempts at answering bits and pieces of the whole have probably created even more confusion because of this. Sorry if I have done that. If so, I believe that my answers have fallen short of the big question and in that context should be considered, at worst as wrong, and at best as incomplete. I am a firm believer that wrong information is worse than no information. After reading through all of the posts, I now believe that we are comparing apples to oranges so I will give it another try to clear up things a little:

In its basic concept, when it comes to a vehicle’s driving axle, there exists two choices in the way in which each driven wheel at either end of the axle housing rotates in respect to the another. The first choice is to have both wheels always rotating the same speed as one another, by being mated to a common driving shaft (in effect). The second choice is to allow the wheels rotate independently of one another by using some form of device that controls the rotational difference between the two to some extent. The two common devices at either end of this spectrum would be the Spool and the Differential.

The Spool is a device that bolts directly to the ring gear. The Spool is driven by the ring gear and rotates on bearings within the axle housing. It has common internal splines that both axle shafts mate into. It effectively locks both axles together as if they were one, allowing for no difference in rotational speeds between these two shafts. It mimics the act of welding the two axle shafts together where their ends meet near the center of the axle housing. The Spool acts as a single solid connecting point between the axles and this connection will cause tires to scrub when the vehicle is turned through a corner. The operator of the vehicle has no control over the operation of the Spool.

The Differential is made up of several parts, usually as an assembly within a case. The ring gear bolts to this case, or assembly, which in turn rotates in bearings the same as the spool above. The Differential has independent internal gears, each with internal splines that the respective axle mates into. These gears, in combination with other internal parts, allow a difference in speeds and even different rotational directions between the two axle shafts. If one axle is forced to rotate 10% faster than the ring gear (for whatever reason) the other will be forced to rotate 10% slower than the ring gear. If one axle shaft is forced to rotate 100% faster than the ring gear the other will be forced to rotate 100% slower. At any percentage above 100 the second axle will actually be rotating in the reverse direction from the first. Unless broken, the Differential never acts as a solid connecting point between the axles, and as such, eliminates any tire scrub through corners. The negative side to this is that any one tire can loose traction and the Differential can deliver 100% of the torque to the axle driving that tire and wheel stopping vehicle motion. The driver of the vehicle normally has very little control over the operation of the Differential. However, a limited amount of control of the Differential can gained through simultaneous application of parking brake and throttle. Even more control can be gained with the introduction of steering brakes.

The Selectable Locker is usually found as an assembly within a case, and like the others, is driven with a ring gear and rotates in the same bearings in the axle housing. The Selectable Locker is sort of like having both a Spool and a Differential all at the same time. It allows the operator to select one of two settings on how they want the Locker to behave. It can be selected to cause a “spooled effect” between the axle shafts in a common housing. Effectively locking the axle shafts together to rotate as one. It can also be selected to cause a “differential effect” between the axle shafts in a common housing. The unit actually employs many of the same parts as a true differential unit. The Selectable Locker requires operator input and is always in one or the other setting– a Spool or a Differential – there is no in-between condition. The Selectable Locker has no provisions for sensing wheel spin and automatically compensating.

The Limited Slip Differential is usually found as an assembly within a case and driven with a ring gear as the others. The Limited Slip Differential is more closely related to the true Differential than to the Spool. It has many internal parts that sense when a tire is loosing traction and directs torque to the appropriate axle to overcome this. One of the main aspects of many Limited Slip differentials is the presence of clutches within the unit. These clutches allow a certain amount of “slip”. The Limited Slip can (depending upon the design) require varying amounts in driver input through the prudent use of brake and throttle in order to operate effectively. This is especially true with those units showing their age. Age and wear are the biggest things that tend to make Limited Slip Differentials less than effective. The correctly functioning Limited Slip Differential is generally more responsive to operator input than a true differential. A Limited Slip Differential can never act like a Spool unless something is broken inside.

The same design, ring gear, case, bearings also applies to the Positive Locking Differential. The Positive Locking Differential should not be called a “differential” at all in my opinion. It has none of the characteristics (and usually none of the parts) found within a true Differential. A better term would be something like: “automatic positive locking traction aiding device”. The Positive Locking Differential is more closely akin to the Spool. It keeps both axle shafts locked together, all of the time, with one exception - it has the ability to let one (and only one) axle unlock from the other when that axle receives force from the surface the vehicle is traveling on causing that axle shaft to want to rotate faster than the other shaft. This action works on the same principle as an overrunning clutch. The Positive Locking Differential does have clutches, but unlike a Limited Slip Differential, they are not the kind of clutches with friction plates that can “slip”. They are called “Dog Clutches” and should not even be called “clutches” in my opinion. A more appropriate term might be “axial gears”. The have teeth that mate together not unlike any other gear set. The Positive Locking Differential requires no input from the vehicle operator in order to switch between “locked” and “unlocked” modes. It is fully automatic. It has no provisions to unlock both axles from the unit at the same time. It cannot transfer all of the torque to another driving axle assembly unless both tires of the assembly it is installed in loose all traction. It has no provisions to operate like a true differential. It operates equally well whether the vehicle is moving forward or rearward, straight ahead, turning left, or turning right. The Positive Locking Differential can be noisy and harsh as it allows axles to “lock” and “unlock” from driven case. This tendency can be overcome somewhat by modifying operator-driving styles.

All traction aiding devices can cause unpleasant results when a vehicle so equipped is driven in a side-hill condition. In a true differential, usually one wheel will spin out while the other acts as sort of a rudder and helps to keep the vehicle headed straight. With a traction aiding device, in a driving axle, both wheels can loose traction in unison causing the rudder effect to be lost. This action can cause the end of the vehicle with the driving axle to swing to the downhill direction. This tendency is true even on relatively flat conditions if the surface is slick enough. Icy crowned roads can found to be especially treacherous while driving a vehicle that is being driven with only one axle when that axle is equipped with a traction aiding device that can not be fully “unlocked” by the operator.


Junior



Follow Ups:



Post a Followup

Name:
E-Mail:
Subject:
Message:
Optional Link
URL:
Title:
Optional Image Link
URL:


This board is powered by the Mr. Fong Device from Cyberarmy.com